Water Saving Shower Monitor & Timer

This Showertime water saving monitor and timer, you will be able to understand how much water you use every time you have a shower. With the bathroom usinh nearly 40% of all water in the home, the shower is the perfect place to start saving water.

The LCD display shows volumeof water in a fun numerical and graphical format. The case and buttons are waterproof, the timer can be wall mounted or lanyard hung and the lithium battery has a life span of 12 months.


With this shower timer and monitor you can set targets for water usage and an alarm will go off when you reach that target. Helps you to save 100's of litres of water and reduce your water bill with programmable targets with a calibrated filling display. The Efergy Shower timer is easy to set up and easy to use, it comes with an eco-container which is used to measure the flow rate of the shower or bath. Once the container is full the monitor is set, so every time you take a shower or bath you can measure the amount of water used.

Display options

*Animated drops - drops alternate between two sets of drops representing the falling of water and filling the tank.

*Water consumption - two large digits show the current estimated water consumption.

*Water consumption tank - 5 segments fill up whilst the shower is in use. Each segment represents 10 units of water.

*The clock display shows how long you have been in the shower, the amount of water used and the time on a 24 hour clock.

* The LCD display - with five segment water container display.

*Time-Litres/Gallons/US Gallons. The water meter will calculate usage in Litres/Us Gallons or Imperial Gallons.

*The pack contains - shower meter, strap, suction cap, measuring bag and batteries.

UK Delivery £2.95

EU Delivery £4.25

Aladdin Auto Vent Standard HV30 C-Automatic Radiator Bleeder

The innovative Hygroseal technology with its long, leak-free life, provides a cost-effective solution to automatic radiator de-aeration. The HV30C operates vertically and horizontally on 1/2" tappings.

Features

• Long, leak-free life
• Replaceable cartridge
• Saves energy & reduces fuel bills by keeping radiators air-free and hot to the top!
• Dispenses with the need for radiator bleed keys
• Reduces corrosion and system noise

UK Delivery £1.95

EU Delivery £2.95

Alladin Auto Vent Micro-Automatic Radiator Bleeder

The innovative Hygroseal technology with its long, leak-free life, provides a cost-effective solution to automatic radiator de-aeration. The Aladdin Autovents Micro operates on 5/6/7 mm 1/8" and 1/4" tappings. It's very easy to fit with no adjustments necessary and no need to drain the system.

Features

• Long, leak-free life
• Replaceable cartridge
• Saves energy & reduces fuel bills by keeping radiators air-free and hot to the top!
• Dispenses with the need for radiator bleed keys
• Reduces corrosion and system noise

UK Delivery £1.95

EU Delivery £2.95

Radiator Reflector Foil

A magnetically fixed heat radiant foil that reflects heat back to the room rather than being absorbed by the wall. This foil can be installed at the rear of the radiator and through it’s high heat reflecting performance, the foil reflects the warmth back to the room and prevents the heat going into the wall. No need for glue, paste or removal of the radiator – this is the quickest and simplest system available today.

Application:

Comeswith 10 metres of self-adhesive magnetic tape for easy installation behind the radiator.
Simply cut the tear proof foil to suit the radiator size, and place the magnetic tape on the surroundings of the foil with the self-adhesive side of the magnetic tape. Now you can easily take this and place it behind the radiator; corrections can be easily made by slidingthe foil at the rear side. The magnetic tape allows corrections but is also strong enough to retain the position once aligned.
If you want to clean or remove, simply take the foil off, clean and then replace again. By using magnetic fixings removal and reposition is very easy.

UK Delivery £2.95

EU Delivery £ 4.25

EcoSaver Powermeter

This mini power meter is designed to measure the power consumption of electrical appliances via a plug and read system. Plug the device into a wall socket and then plug any electrical device into it thus allowing it to display how much energy it being used. The Powermeter displays accurately and precisely how much energy is being used so the user knows immediately the associated cost to run the appliance.

Features

*Voltage display (V) 90-250V

*Current Display (A) 0.1-16A

*Power consumption display (W) 0.2W-3120W

*Display operating time in hrs/mins/secs

*Display costs in £ (price programmable)

*Maximum current 16A

UK Delivery £2.95

EU Delivery £3.95

Ecobutton

The ecobutton™ is an illuminating USB device that acts as a reminder and a prompt for the user to press it's butto at every opportunity whenever the computer is going to be left idle. This could be from taking a phone call or break, to doing paperwork or going to lunch and meetings where otherwise the
computer would normally be left on. This is because people generally do not like turning off their computers because of the time it often takes to restart. When the ecobutton is pressed it engages the computer into energy saving ‘ecomode’. This ensures that both the computer and monitor are set to operate in the most efficient, lowest power mode available, which actually draws only the same nominal power as when the computer and monitor are turned off!
When you need to use the computer again, simply press any key to instantly return to where you left off!

Did you know?
Computers and monitors can account for half of the electricity used in a typical offi ce. A single monitor left switched on overnight can use the same energy as a laser printer producing 800 A4 printed copies - and don’t be fooled by a screensaver – the computer is still working at full power to run this!

*One third or more of energy used on a PC and
monitor is wasted energy!

*This wasted energy can cost around £50 or more a year.

The savings
The amount of energy that a computer and monitor use varies depending on its age, model, and the programmes and applications in use. A PC switched on 8 hours a day engaging ‘ecomode’ for 3 hours could save around £50 in electricity cost per year. If the PC is left on overnight the saving could be £100 or more - or the equivalent of 600kgs of CO2. Indirect savings can be made with air conditioning systems as they do not have to work so hard because less heat is generated from computers actively using the ecobutton. Because the button stays illuminated even during ecomode, this can provide a useful reminder that all unnecessary computers, lighting, heating and air conditioning etc... should be be switched off at the end of the day.

UK Delivery £2.95

EU Delivery £4.25

Standby Energy Saving Starter Kit

The Standby Remote Control combines energy saving with the luxury of switchingyour electrical devices on or off by remote control.With this product you can turn off your electrical devices simply by using the remote control, cutting off the electric power. By using this system your device will not be left in standby mode and will therefore save standby power consumption of all the devices connected to the remote socket.The base-set comes with a remote control and either one or three remote sockets, depending on the pack purchased (3 pack also available from EcoGadgets). Several sockets can be controlled by the same on/off (zone) switch of the remote control, offering many combinations of use. Easy to set up, each remote socket can be programmed (self learning) to react to either button (zone) 1,2,3 or 4. Enjoy the luxury of remote controlled switching on/off and save energy! The remote control operates on radio frequency, so the sockets can be placed out of sight if required.


SPECIFICATIONS:

*Voltage: 230V / 50 Hz
*Rating: 230V / 3.100W max.
*Learning code: more than 1 million
*Remote Frequency: 433.92 MHz
*Remote range: 20 Metres
*Code setting: Learning
*ON/OFF indication: LED
*Battery Type: L1028 * 1-12V DC Alkaline

UK Delivery £2.95

EU Delivery £3.95

Standby Spare Plug Socket

Additional socket for the Standby Energy Saver starter kits or full sets. Works with the existing remote controls from original packs.

K Delivery £2.95

EU Delivery £3.95

StandBy Energy Saving 3 Socket kit

This Standby Remote Control system has replaced our Standby Buster 3 socket kit. It's the exact same product but comes in better packaging and at a cheaper price to you. It combines energy saving with the luxury of switching your electrical devices on or off by remote control. You can turn off your electrical devices simply by using the remote control, cutting off the electric power. Using this system your device will not be left in standby mode and will therefore save standby power consumption of all the devices connected to the remote socket.The base-set comes with a remote control and three remote sockets. You can add additional remote sockets(available separately) for operating with one single remote control. Several sockets can be controlled by the same on/off (zone) switch of the remote control, offering many combination's of use. Easy to set up, each remote socket can be programmed (self learning) to react to either button(zone) 1,2,3 or 4. Enjoy the luxury of remote controlled switching on/off and save energy! The remote control operates on radio frequency, so the sockets can be placed out of sight if required.

Specifications:

*Pack contents: 3 sockets & 1 remote control.

*Voltage: 230V / 50 Hz
*Rating: 230V / 3.100W max.
*Learning code: more than 1 million
*Remote Frequency: 433.92 MHz
*Remote range: 20 Metres
*Code setting: Learning
*ON/OFF indication: LED
*Battery Type: L1028 * 1-12V DC Alkaline

UK Delivery £3.95

EU Delivery £5.45

Efergy Energy Reading Meter

This is the new improved MK2 version of the efergy smart meter. It's a wireless smart electricity meter that helps you track how much energy you are using, encouraging a reduction in energy while saving money, because the monitor gives instantly an accurate reading of how much energy you are consuming. It provides simultaneous information on average daily (energy & costs), instant information (power & costs), historical consumption (energy, costs and CO2).

Efergy tells you every few seconds how much power you are consuming, how much money this is costing you and an estimate of your personal contribution to climate change. If you turn a set of lights ON or OFF, you can see INSTANTLY the change this has to your energy use. Once you have this information to hand means you, your family, or business, can visually see the benefits of saving energy.

The data is stored daily in an easy to access CPU memory so you can actually see the effects of your changing energy habits. Comparing day-to-day usage gives you direct feedback of how daily changes of habit toward energy use can have an effect on costs and estimates the personal contribution to the climate change in terms of carbon emissions. You can store data for 7 days, 4 weeks or 24 months.

The efergy smart meter is an excellent educational device. It is easy to use, displays personal energy consumption and increases awareness of important issues related to electricity, energy and the environment. Great idea!

Specifications:

* Frequency: 433.52MHz
* Transmission Time: 6s, 12s or 18s
* Transmission Range: 40m-70m
* Sensor Voltage Range: 110V-300V
* Measuring current: 50mA-95A
* Memory: 64K

The box contains:

1 x Efergy Sensor

1x Transmitter

1 x Elite Display Unit

2 x Velcro Fixing Pads

UK Delivery £3.95

EU Delivery £5.95

Radiator Booster MK2™

This is the new improved MK2 version of the successful Radiator BOOster™.

• Now with automatic thermostat control – switches on at approx. 32 degrees Celsius
• Now adjustable to fit smaller and larger radiators
• Now made from recyclable Polycarbonate
• Now manufactured with one (more powerful) fan for quieter and cheaper running
• Will save an average household between £70 to £140 on heating bills per annum

How does Radiator BOOster™ 2 actually work and save energy?

This ingenious device works in 2 ways;
1) Your central heating boiler will use around 15 kilowatts of energy every hour (some even more). The clever fan arrangement within the Radiator BOOster™ draws heat from your radiator, heating your room in up to half the time, allowing your boiler to shut down much sooner. If you could save just one hour a week of your boiler working, you would save 15 kilowatts of energy. You could easily find the savings more than this, between 7 and 14 hours/week (over 100 kilowatts) during the colder
months.

2) As your radiator heats up, the ‘rear’ surface normally radiates heat onto your wall, heating this up, which in turn is lost through the wall structure due to conduction. The Radiator BOOster™ sucks most of this wasted heat and fires it into your room, significantly reducing the losses, saving you even more energy. It really is as simple as that!

How much energy does it really save?

This will depend on how you use the Radiator BOOster, and for how long. But UK energy providersstate that reducing your thermostat setting by one degree Celsius could save the average home £70/year or 10% of your heating bills. Most tests carried out with Radiator BOOster™ have achieved more than 2 degrees reduction.

Can it be used with Radiator Covers?

YES. Most definitely. Provided you can fit the device in place under your cover, you will save up to 3 times as much energy. Covers prevent a radiator from ‘radiating’ its heat, relying solely on
‘convection’. Radiator BOOster™ enhances that convection at least three fold, distributing huge
amounts of trapped heat.

Can I leave it running 24/7?

YES. As the new Radiator BOOster™ 2 has in built thermostat that switches on at around 32 degrees Celsius and switches off when the radiator temperature drops below this point.
Should I turn it off when my radiator cools down? This is an option, but is not necessary as the thermostat control will automatically control the use of the integral fan.

Could I plug it into a timer unit to avoid me remembering to turn it on/off?

Yes. A standard ‘event timer’ could be used, the power supply plugged straight into it.

Surely the materials used to manufacture the Radiator BOOster™ themselves impact on the world’s resources?

Yes, like most things this is true. But we have designed the product to use the absolute minimum of materials and substances, and in return achieve huge energy savings over many years. The ‘trade-off’ is well worth doing. The Radiator BOOster™ 2 is also fully recyclable.

My radiator is very long. Do I need to use two of these?

You can do, but it should not be necessary. The simple movement of air created by Radiator
BOOster™ will normally lead to good convection in your room.

Where should I place it on my radiator?

As far to the back and centralised along the length of your radiator should optimise the performance. However, if you place it to one end, it should still work adequately. On some radiator designs you will find that the device will drop down slightly behind the top of the radiator. This further enhances the performance.

Can I use it on oil filled radiators, electric storage radiators, or electric convection radiators?

NO. These types of radiator reach far higher surface temperatures than water filled radiators. These higher temperatures will distort and damage the housing and fans of Radiator BOOster™.

Can I use it in my bathroom, shower room, sauna room, outbuilding, etc?

NO! Radiator BOOster™ must not be used in a damp or humid environment under any circumstances.
How much electricity does it use, and is it safety approved?

The Radiator BOOster™ has been tested and approved by an independent laboratory, and conforms to all aspects of CE Certification. Each fan is rated at < 1.0 watt, 12v DC, and each unit is supplied complete with a full set of instructions. Should you operate a Radiator BOOster™ for 500 hours, it should use approximately 1kW of electricity (less than 13p for most homes).

Will I need to put one of these in every room?

We would recommend you place one in each room that you regularly use, but it shouldn’t be
necessary for other rooms. After all, you could unplug and move one very easily if necessary.

My nearest power socket is a long way from my radiator.

Each unit comes fitted with a 1.8metre power lead, which should suit most situations. However, there is a 2-metre extension lead available.

Do I need to clean the device?

Yes. As with any fan, dust will build up on various surfaces, which will seriously impair the
performance and reliability of the device. You will need to clean it periodically using a lint free
cloth. Take care with the fan blades as they are very delicate and can break easily.

Can you hear it working?

YES. The small fans used in Radiator BOOster™, like any fans, make an audible humming noise."The fans used in Radiator BOOster are similar to those used in home computers and operate at around the same audible level." During the summer most of us use large noisy desktop/ pedestal fans to help
keep us cool, and in the winter noisy electric fan heaters to help keep us warm. Radiator BOOster™ costs virtually nothing to run and is considerably quieter than either of these.

Sometimes it is quieter than other times. Why is this?

The fans can take some time to settle down and perform at their optimum, and they are also very
sensitive to temperature. The sounds will vary from time to time, but this is normal and should cause no concern.

I’m allergic to house dust. Will this make things worse?

For the first few times Radiator BOOster™ is used it may stir up a little loose house dust from around your radiators, but within a couple of days this should settle down and the situation return to normal.

UK Delivery £3.45

EU Delivery £5.95

Save Petrol with Magno Fuel

SORRY-OUT OF STOCK

Magno-Fuel has been tested to give fuel savings of up to 15%. It provides better combustion and more power from your engine while reducing pollution. Simply fix the Magno-Fuel around the fuel line and fasten with the cable ties provided. Only after a short time will oxygen molecules be embedded between the fuel molecules, ensuring a better combustion. Bloch and Purcell were awarded the Nobel prize for their work on magnetic fields on solid, liquid and gas substances. By using the latest developments with magnets, Magno Fuel was born. Suitable for petrol and diesel engines.

UK Delivery £3.45

EU Delivery £5.45

PowerSafer PS1.1

This great energy saving gadget is designed for single TV applications. Simply connect into your chosen electrical appliances and this device will let you keep you them on standby with-out using any energy. Standard standby mode energy use can increase the wear and tear of all appliances as well as crank up your electric bill. This device should pay for it's self within 1-2 years depending on how often and how many devices you regularly leave on standby. The only requirement is that your device has an on/off button and remote control.

UK Delivery £3.45

EU Delivery £4.95

PowerSafer PS3m

A step up from the PS1.1, this energy saving gadget is designed for multiple applications such as TV, Hi Fi, games consoles and home theatre kits. Simply connect into your chosen electrical appliances and this device will let you keep you them on standby with-out using any energy. All you need is multi plug block to plug the PS3 into and you are ready to go. Standard standby mode energy use can increase the wear and tear of all appliances as well as crank up your electric bill. This device should pay for it's self within 1-2 years depending on how often and how many devices you regularly leave on standby. The only requirement is that your device has an on/off button and remote control.

UK Delivery £3.45

EU Delivery £4.95

PowerSafer PSX

This is the latest energy saving device from the PowerSafer team. This device will do multiple appliances connecting up to 5 devices to the input using a 5 way multi block adapter (not included). Max load 480 Watts.It has a built in surge and lighting protection, protecting your equipment from power surges.The average household can have many appliances left on standby at any one time-using the PSX you have the convenience of using your remote controls and never need to unplug at the wall or switch off devices again. On average the PSX will save you between £30-40 per year depending on how many gadgets your used to leaving on standby.The new PSX is the one of the most advanced standby devices on the market!! Just connect your equipment and follow the instructions.

UK Delivery £3.95

EU Delivery £5.45

Souvenir Cranwell Battery Regenerator

A great environmentally Friendly Low Current System for recovery of discharged alkaline batteries.Not long on the market this technology is based on a Thomas Edison patent of 1922. Thomas Edison discovered that the main reason why alkaline batteries becomes discharged is the accumulation of impurities and foreign matter on and in the positive electrode and the coating of the active material with a scale or crust which seriously impairs the efficient operation of cell.

The Cranwell Battery Regenerator replicates this process by thoroughly and gently cleaning the electrodes over an average 72hour period but does it inside the battery itself. This process is absolutely safe and dos no damage to the battery. Nothing is added to the battery; it just releases the potential that is already there. One battery can be regenerated up to 100 times.
Capacity of regenerated batteries depends on manufacturer, discharge and storage conditions. Our and our customers’ tests show that most of the alkaline batteries, for example Duracell Plus, Duracell Ultra, Segasa Evolution, Energizer Ultra, many own brand batteries such us Morissons, Tesco etc. can be regenerated up to 95% of its original capacity. Power consumption of the Regenerator is very low and cost of regeneration is less than a tenth of penny.

The Cranwell Regenerator can also regenerate some non-alkaline batteries. For example Heavy Duty Single-Use batteries (Panasonic Special, Sky and etc) can be regenerated up to 60% of its original capacity. Titanium batteries (Energizer E2) can be regenerated up to 80% of its original capacity.

Summary:

• Advanced processor control for simple plug and go operation.
• 4 charging docks for regenerating AA and AAA
• Simultaneous regenerating of mixed types and sizes
• Completely safe againstovercharge, overheat, short-circuit,
and polarity reversal
• LED indicator turns off when renewing process is complete
• Regenerates most brands of batteries
• Saves money

Technical specification

Input Voltage: 100-240V DC 50-60Hz
Output Voltage: 1.8V DC per channel
Output Current: 35mA max. per channel

Below, is the difference between existing SINGLE USE BATTERY CHARGERS and THE CRANWELL ALKALINE BATTERY REGENERATOR.

Existing single use battery regenerator

-Single-use battery chargers use pulse current up to 200 mA
or/and temperature on recharge.

- Pulse current is used for avoiding overheating single-use
battery because between current pulses, battery is cooling.

- Temperature control is used for quick recharge, current
breaking or switching on fans when battery overheats. The
simplest method for temperature control is measurement of
internal battery resistance.

Advantage:

1.Fast charging (up 16 hours).

Disadvantages

1. All batteries are different. They have different quality of
electrodes surface and electrolyte heterogeneity. So a setup
suitable for one battery may not be suitable.

Another battery even though it is of the same type or in the
same lot. As a result some batteries being charged in the same
unit may overheat leading to possible leakage, boiling or even
explosion. No one method can be used to measure individual
battery overheating; only an average temperature can be
measured.

Overheating causes irreversible change of structure of
electrolyte and electrodes. This is why alkaline batteries
cannot be recharged more than 5-10 times and why single-use
batteries cannot be recharged.

2. Chargers do not clean electrodes and do not remove the crust
which forms inside the battery. This crust is the main cause of
overheating leading to the degradation of batteries

3. Chargers have complex circuitry resulting in high costs and
low reliability.

Cranwell battery regenerator

It uses a low current - no more then 35 mA and/or some
additional influence. Electrodes are cleaned using patented
system which recovers electrolyte potential and improves
structure of electrode.

Advantages

1. Our method is universal for all types of batteries ( all
batteries have electrodes and electrolytes).

2. Small current and/or other low influences means that
overheating of a battery is avoided.

3. Number of recovery cycles significantly more than 5-10cycles
used by chargers.

4.Simple circuitry means low production cost and

high reliability. We can therefore offer a long guarantee period
and free service.

Disadvantages:

1.up to 72 hours for recovery.

UK Delivery £2.95

EU Delivery £4.25